Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
The writer is making a number of great points relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this article down the page.
Installing a bathtub isn't specifically rocket science, however it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bath tub with a new one is also a reasonably difficult project. If the old bathtub is readily easily accessible, the job can move immediately; if you need to open a wall to eliminate the old tub as well as position the brand-new tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to vacate the old bathtub as well as set in the new one. Ensure you have qualified yourself for the job as well as fit trying it. Rather than employing a specialist to take over a halfway-completed job, it is much better to consider using one prior to you begin. Chances are you might require a specialist plumber to make tube links.
This short article will certainly aid you mount a brand-new bathtub in your restroom if you have actually already bought a brand-new bathtub as well as do not require to change the plan of your previous water pipelines.
Your devices as well as material list must comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you should do is disconnect the water system. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome due to the limited accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been gotten rid of, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. When the faucets have been removed, the holes in the bath/basin will have to be cleaned of any old securing compound.
Prior to moving on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making sure that the washing machines remain in area between the tap and also the sink. Protect the faucet in position with the producer offered backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind ought to be attached to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub till the level reads degree.
To mount taps, fit all-time low of the furthest adaptable tap port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water system as well as inspect all joints and new pipework for leakages as well as tighten them if needed. Fill up the bath tub and likewise check the overflow outlet and the typical electrical outlet for leaks.
Ultimately, repair the bath paneling as explained in the maker's instruction manual. Tiling and sealing around the bathtub must wait up until the bathtub has actually been made use of at least when as this will certainly resolve it right into its last setting.
Preparing for the Setup
First of all, the supporting framework supplied with the bathroom ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to see to it that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets device to avoid pressure on the tub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its last setting.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to crack an inflexible seal, causing the water to permeate the wall surface between the bathroom and the tiling, resulting in problems with wetness and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the bathtub with water prior to securing, to enable the activity experienced when the tub is in usage. The sealer can split relatively early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily readily available on the marketplace. It is suggested to fit the ceramic tiles utilizing waterproof or water-proof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on How to Install a Bathtub, I assumed sharing that blog post was really useful. Enjoyed reading our piece of writing? Please share it. Help other people discover it. Thanks a lot for your time. Kindly pay a visit to our website back soon.
About This Report this page